How to fit a fireplace back panel

From here, fit the mantel again and pull the back panel forward to touch the surround. The mantel will hold the surroun but there will be a gap behind the back panel which will require packing with either the rebate strips that you have removed or MDF, plasterboar pine, etc. Use tile adhesive or no more nails to fix the back panel to the packing, and. As a fireplace specialist we are often asked how to fit a back panel against a wall.

Essentially the answer is more complex than it initially appears and will depend. You will need to know the size of the cut out which is recommended for your gas fire and the clearance at either side. The material used to push the back panel forward does not need to be non-combustible if you are fitting an electric fire as there is no direct heat behind the back panel At Creative Fireplaces we always speak to our customer prior to manufacturing a fire surround (all fireplace are made to order in Nottinghamshire) to ensure that we have the correct rebate for your installation. No its a hell of a lot easier! Your done, fit fire and warm your toes!

The back panel now gets centred behind the fire surround and it needs to be pulled forward to meet the inside legs of the fire surround (Rebate) Once in position, the remainder of the plaster mix us used to fill any gaps around the fireplace opening and the chimney opening to ensure none of the gas fire fumes can get behind the fireplace. So when it was time to fit the back panel and surroun they had a firm base to sit on. Applied four dollops of sticky to the back panel and temporarily held that in place with a clamp.

Most of our mantelpiece have a one inch rebate, meaning that when a standard one inch back panel is fitte it will fit securely between the wall and surroun with the inset fire recessed into the wall cavity behind. Big Range Of Fireplace Back Panels. Free Fast UK Wide Delivery. Eligible for FREE UK Delivery. Installing a fire back into an existing hearth and fire surround.

All solid fuel installations must be carried out by a registered HETAS installer, or through Building control. I have removed an old fireplace and just got a new one. Anything i can do like fit the hearth or will installer want to. Real wood Veneer Fireplace surround.

If you are NOT fitting a stove with “marble back - panel and surround” ( back panel and surround shown in the first picture on this page) then your recess has to end up exactly the right size and this can take some doing. So if not fitting back panel and surround check out steps 1-(otherwise skip 1-5). Step Packing out with non-combustible material to ensure fit against legs of surround. Fire Surrounds (products). We offer a great range of fireplace surrounds to help transform your home.

If you already have a fire within your home, changing your fire surround can transform the look of your room and act as extra storage. If sizes are required smaller than the above, fireplace panels can be cut to the required size using an angle grinder fitted with a diamond tipped masonry blade. Place the back panel centrally on the hearth and screw it to the wall with the fixings supplied. Instea stand it vertically against the wall and hold it in place by fixing the mantel. Great discounts and savings on top home brands.

In of cases, to be thinking about installing a new fireplace means there has been, or is, an existing fireplace in the property. In some cases it is simply a. MUST NOT be used as instructions for fitting. Press the panel in place at the back of the fireplace box. Place a board against the panel to hold it in place while the mortar sets.

Use the back panel to add a lovely smart finishing touch to your fireplace and create a realistic look for a gorgeously cosy feel. Create a warm, sophisticated look around your gas or electric fire an. Am about to start fitting a 4-piece 30mm marble fireplace surround and hearth for a solid fuel fireplace in the lounge. Bedding the hearth onto the concrete screed floor is straight-forward enough.

The hearth and fireplace back panel are essential components if you want to make the most of your fire and create a stunning and consistent decorative style in your house. Hearths are also important from a practical perspective, so we highly suggest that you don’t overlook the importance of a fireplace back. On fitting the hearth and surroun you might find it easier to remove the skirting either side then install the hearth and surround. Magnets are most common with trim kits that will fit onto a metal fireplace. Before you begin the installation process, you should make sure that the fireplace is off and cool to the touch.

With the brackets attached to the header, as shown above, position the header carefully on to the legs and mark off the position of the holes in the fixing brackets. Measuring the correct rebate ensures that your new surround will fit flush back to your existing inset, an example being your back panel. There are two ways in which you can measure an existing rebate, follow the simple steps below. We’ll come back to the creating and fitting of the closure plate shortly so forget it for the moment.

At Fireplaces Life our staffs are often asked if a fire will fit into their existing or back panel or what size they need if buying a new back panel , in most cases. If the fireplace has an extended rebate you may have to space the back panel from the wall with Rockwool slab, Thermolite block or similar product types. Note the space between the back panel and the wall should be filled with non-combustible material taking into account the intended purpose of the fireplace.

We do not fit fireplaces or gas fires but we do have a list of recommended fireplace fitters and CORGI registered gas fitters. You can fit a fireplace yourself and this guide will show you how but it does require a level of building competence.