Fitting stair runner round corners

I want to fit a narrow runner to a eight tread staircase that turns 1degrees top to bottom (in an old house, beside the chimney). Gripper and underlay should be used under stair runner carpets in the same way as they are used for any other carpet. When a carpet is going up the straight run of the staircase, the carpet should be equidistant from the strings of the staircase on both sides so that it lies dead centre on the staircase. Fitting a stair runner carpet is a relatively simple project that involves a number of simple steps - measuring and marking your staircase, cutting and stapling your underlay, securing the carpet and screwing in your metal stair rods.

Fitting a runner with stair rods can be done safely, neatly and cost-effectively with few tools, and in many ways is much more suited to the DIYer.

The rods actually make it much easier. Install carpet padding along the stairs where the carpet will lie. Cut and fit the padding to each step starting from the bottom and working your way up. When stapling the runner to the woo start at the bottom riser and staple just below the nosing of the tread. Bring the carpet over the nosing, pull it tight and jam it into the corner onto the pins of the strips using either a flat, broad knife or a knee-kicker carpeting tool.

Don’t staple it to the next riser until you are sure it is perfectly flat on the tread. Stair rods are purely decorative and it is essential to fit your stair runner using gripperods.

Gripperrods come in both medium and short pin depending on the thickness of the carpet being fitted. Although mathematically impossible to match stripped carpet on turning stairs it is still possible to achieve a very good look. If you are using a stair runner that leaves a gap at either side, the fitting instructions are the same as below – just make sure the gripper strips are the correct width. It will help if you mark a line on each step that you can follow to ensure you have an equal amount of space at each side of the runner. Friendly, Personal Service And Exceptional Products.

Cut a piece for each winding stair. Using the remaining balance of the runner , cut a piece for each winding stair. If for example you have winding stairs. Depending on the construction of the stair , the tread is fitte then the riser.

Or all the treads then all the risers. Stair nosings should ideally be smooth and rounded as sharp square edged nosings can cause rapid wear to the runner. Learn how to install a stair runner in this video. Carpet Advice From The Experts. Choosing and caring for your carpet runners and carpets can be a daunting and tricky task at the best of times.

Measure the depth and the width of one stair tread and the height of the stair riser.

Count the total number of steps. Multiply the number of steps by the tread depth and riser height to calculate the length of carpeting needed. Add about per cent to that figure to account for extra carpeting needed over the nose of the trea the staircase corners and possible mistakes. How to fit a Stair Runner Please note that this guide is for the fitting of straight stairs only. For winding stairs or those with a half landing and turn, we strongly recommend that you employ the services of a professional fitter.

Installing a stair runner on a straight staircase is a relatively easy project, even for novice do-it-yourselfers. Winder stairs that turn corners are more challenging, but still doable with our expert instructions. Use a knee kicker to push the carpet tight into the corner of the tread and riser while using a stair tool to wedge the carpet into the corner between the tread and the riser. Repeat steps six and seven as you work your way up the stairs. Well, there’re several ways to do this.

Let’s briefly look at the options. This article details how to install carpet on stairs , covering the full tread and riser (i.e., not a stair runner ). However, if you are looking to install a carpet runner on your stairs , the following instructions can be modified accordingly. Step by step instructions on how to fit a carpet runner on your stairs with images of a professional fitter. If you need extra help, contact us for free help and advice.

Fitting of carpet to the stairs The method of fixings for a fitted stair carpet is the same as that for a runner. A major reason for this is the development of tools designed specifically for the job. Hi gang I am looking to fit a runner to my stairs instead of carpet. Old carpet has been lifted and I have almost finished sanding the stairs (pain in the arse) ready to varnish, so now I am. The carpeting on stairs takes a lot more abuse than regular room carpeting, and it often wears out much sooner.

A curved stairway actually has two rise and run layouts—one at the inside or tight stringer, and a different layout at the outside stringer. Laying carpet or a stair runner on a straight staircase is quite straightforward and the method is described below. Designers and Makers of unique stripe runners and rugs in natural fibres. The stairs need fitting on gripper and underlay as the rods are purely decorative, each of the steps needs cutting indivudually and shaping correctly, and the stair edges need binding also. I need to install a carpet runner down a staircase.

This is a typical installation with the brass bars in the corner between the tread and riser to hold it down. The difficulty is that the staircase has a turn near the bottom where the steps are triangular in shape. Stretch the carpet into place with the knee kicker and wedge the cut end.

All you do (If the nosing is the same thickness as the flooring) is measure the height of the trimming joist and transfer that onto the newel starting from the underside of the nosing. With skilled fitting the carpets can be taken round winders and turns and mitred on corners to give a superbly tailored finish.